Payment & Shipping Terms:
|Material:||Stainless Steel Plate||Application:||Filters|
|Hole Shape:||Round, Can Be Customized||Surface Treatment:||Smooth|
|Width:||1.22 M Or Below||Color:||Silver|
|Technique:||Perforated||Length:||2.44 M Or Below|
perforated stainless sheet,
perforated stainless steel mesh
Thickness 0.5mm Perforated Metal Screen 201 Stainless Steel Sheet
Perforated round hole metal is typically produced from coil and staggered (60 degree pattern) is standard. Variations include 45 degree staggered, and straight line pattern. It can be produced in widths up to 60" and in any length (typically under 250" for shipping purposes). It can be lightweight in gauge, have small or large optically appealing openings and be very suitable for many architectural and display uses. Whether used for technical or decorative applications, round hole perforations are the most frequently used in perforated products. Geometrically, a round hole is the most solid shape.
Round hole,Slot hole,Square hole,Hexagonal hole,Plum blossom hole,Scale hole,Cross hole,Triangle hole,etc.
Now let's talk about the arrangement of punch holes:
(1) straight line
(2) 60 ° staggered
(3) 45 ° staggered
(4) square hole
(5) long round hole
(6) long round hole
(7) hexagonal hole
Perforated stainless steel is either T304 stainless steel sheet or T316 stainless steel sheet that has been punched with a series of holes to give you a nominated pattern. The pattern can vary depending on the hole size, distance between holes and the thickness of the material.
Thickness of Metals:
Steel:Use“Manufacturers”Standard Gauge for steel sheet.
Stainless Steel:Use the U.S. Standard Gauge Table.
Monel: Use the U.S. Stangard Gauge Table.
Copper, Brass, or Muntz: Use the B&S Gauge Table.
Aluminum: Use the B&S Gauge Table.
Round Perforations: Staggered (60 degree pattem) is stangard. Vaniations include 45 degree staggered, and straight line pattern.
Square Perforations: Staggered or straight line pattern.
Slotted Perforations: Side staggered, end staggered, or straight lines. Slotted perforations will be round end slots: specify if square end slots are required.
Other Perforations: Available upon request.
Spacing of Perforations
Spacing for large perforations will be designated be either Centers of perforations, or by the Open Area required. Spacing for small perforations will ge designated by either Centers, or Open Area, or if more practical, by the Number of Perforated to the Square Inch.
Pattern of Perforations:
Staggered Perforations ,both Round &Square: Direction of the stagger will normally be the short dimension of the sheet. Straight row of hole is normally parallel to long dimension of sheet.
Slotted Perforations: The long dimension of the slots can be fumished with either the width or length of the sheet in most cases.
Perforated Stock Size Sheet & Plates: The long sides of the sheet will be suppiled with minimummargins. The short sides of the sheet will have either minimum margins or no margins.
Sheets & Plates Re-sheared after Perforating: Special margins are available to specifications but the must carry a tolerance within the limits of the perforating tool.
Unfinished end pattern is standard in the industry.
Flatness of Sheet &Plates:
In the majority of requirements, perforated sheets or plates can be furnished to AISI flatness tolerances. Before ordering any of the following special requirements, discuss then witn our sales department:
Perforated sheets with extra wide margins.
Blank areas required within the perforated area.
Perforated sheets with very large percentage of open area.
Heavy page metal in relation to the size of the perforation.
Stretcher leveled sheets.
Guidelines for Minimum Hole Size/Minimum Bar Width:
The rule of thumb for pertorating is that thehole diameter should not be less than the thickness of the material. The closer to a 1-to-1 ratio, the higher the probability of tool failure and the greater the precautions necessary to avoid it. Modifiactions can be made in certain instances at additional costs. For stainless steels and similar higher strength materials, it is perforable to specify at least three thickness gauges thinner than hole diameter.
The same general rule applies to bar width. The bar width should be greater than material thickness because of the increased number of punches and therefore, increased perforation tonnage. The bar with can be adjusted at increased costs.
|Diameter D||Pitch P||Open area||Thickness|
Perforated stainless steel has many various uses, including catering for the architectural, chemical, mining & refining, the uses are endless. The following items are generally available from stock, or with a very short delivery. It you don't see what your looking for, we can custom punch many patterns.
This perforated metal rust and corrosion resistance good, isn't afraid of moisture and water. It can have a long life in a wet environment. The stainless steel perforated metal is very suitable for use in drainage rack, building ceiling.
|Name||Perforated Mesh / Perforated Sheet / Punching Mesh / Decorative Mesh|
|Material||Aluminum Sheet,Steel Sheet,Galvanized Sheet|
(1)For aluminum material
(2)For iron steel material
|Sheet size(m)||1x1m, 1x2m, 1.2x2.4m, 1.22x2.44m,etc|
|Hole shape||Sound ,square,diamond,hexagonal,star,flower,etc|
|Perforation way||Straight perforation,staggered perforation|
|More sizes and designs can be customized.|
1. Farm fence, zoo fence.
2. Window screen, filters, barbecue mesh.
3. Sport fence, border fence.
4. Grills, architectural accents.
5. Mining, medicine, grain selection, indoor sound insulation, silencers, ventilation, grain storage and machine protection
If you need to consult the price, please contact the business department by e-mail.
We has had the ability to perforate for several years. Whether a simple round hole pattern or a complicated multi tool pattern we has the ability to perforate to customer requests and specifications.
1. Reasonable price, best quality.
2. 24 hours on-line service, efficient and convenient after-sale service.
3. We have company and provide the direct price.
Contact Person: Lisa Ren